It is your responsibility to ensure this part will fit your application. . Additional helpful information may be found in other service literature for your engine. I made the post assuming others have wanted to do this and have done so? We accept Visa, Master Card, Discover Card, and Pay Pal. Refer to Shifting and Speed Control. To avoid overpowering a boat designed and rated for remote steering, contact boat manufacturer for tiller-steered maximum rated horsepower. If your motors tiller is less than that, it should work.
If the engine does not stop running, see your Dealer. You will be opening a can of worms doing all that work on that motor, if at all possible. Keith Davis 2015-05-06 The inside diameter of the extension is 1. Undisclosed 2012-08-05 If your tiller handle is less than 1. Start Button While seated, press the start button.
It is pretty well made. The outboard will run at idle speed. I will port the intake myself. Twist and remove all spark plug leads. We have fully boat tested this motor and it runs excellent.
Thanks for the pic Chine. Contact with underwater obstructions may result in loss of control and personal injury. The gearcase of this outboard extends below the water surface and could potentially come in contact with underwater obstructions. To prevent accidental starting while servicing, disconnect battery leads from battery. Here are some pics of what I got done tonight before having to make my boys dinner. After Engine Starts Check the water pump indicator. Apply soapy water to the inside surfaces of grommet and install cables and fuel line as shown: Place the grommet into position in the lower motor cover.
Steering friction device is not intended to hold boat on a set course. Tiller is equipped with a throttle friction adjustment knob. That's why the shift handle is where it is so you're not reaching around. Crank the engine no longer than 20 seconds. Please look at the pictures to get an accurate description of detail. Place tiller handle on steering arm from the bottom.
I'll have to wrap the motor handle with something to make it wider. Even thinking on boaring the carb and jets myself to match the 30hp? Use tie straps to secure harness to throttle body bracket. I also think the cables will twist easier due to the straight shot to the linkage. Everything you see is included, handle, cables, brackets, kill switch etc. Install locknuts on screws on top of steering arm. I can't afford a new E-tec with the tiller and shifter in the middle like I wanted this year so I am going to make it myself.
I purchased a fresh water boat with a Mercury 25 that had less than 30 hours on it for my elderly parents. This sale is for one used Mercury Mariner outboard tiller handle steering bracket. This engine starts, idles, and runs great. I suspect it would work. There is also an opening so you can press the kill switch.
Failure to provide start-in-gear protection could create a risk of personal injury or property damage. And among other mods I am going to do to it I decided to move the tiller handle in toward the center of the motor. If there is debris in the fuel filter, it must be replaced. A boat designed for remote steering might have a lower maximum rated horsepower for a tiller-steered outboard than shown on the certification plate. And next is to make a custom bracket for the tiller and cut the hole through the front of the lower housing. I can't imagine trying to dock when sitting on the port side.
At each outing, inspect clip and lanyard for cuts, breaks, or wear. Connect the clip to the emergency stop switch. They could not get used to the tiller handle so my merc mechanic converted it to a remote steering. There is a reason why all tillers are mounted that way, from the day of conception. Reduced control of the boat could result in loss of control by the operator, creating a risk of personal injury or property damage.
Undisclosed 2013-05-12 I put mine on a 2hp Hinda and it is too big. Apply Triple-Guard® grease to threads of steering friction adjustment screw. Always shut off the outboard when your boat is near people who are in the water. To avoid damaging the tiller handle when tilting the outboard up, position the outboard to clear obstacles in the motor well and boat. Most customers agree it accommodates almost any tiller outboard.