Electrical components such as your map light, radio, heated seats, high beams, power windows all have fuses and if they suddenly stop working, chances are you have a fuse that has blown out. One arm goes to the door handle on the outside of the door and one goes to the handle on the inside of the door. Use duct tape to hold it up, if necessary. Screws from behind the door handle lever. I installed Dynamat on the inside doors mostly following these pi … ctures--and the speakers need to come out to do this installation. If your Civic is experiencing electrical problems, you should always check the fuses first, because they are relatively easy to check and cheap to change. The panel is held in place by 4 screws - two behind the door release handle remove the small trim piece behind the handle that hides the screws , one underneath the upper pocket, and one hidden under the window control panel.
Then you will find this helpful guide pretty useful. By - March 10, 2015 This article applies to the Honda Accord 1990-2002. There are 3 screws inside there as well. Next, you'll need a flathead screwdriver to push out the clip holding in t … he window crank. There are two plastic screw on the trailing edge of the door panel that will unscrew. I use a flat head screwdriver to get underneathe it and start working my way around.
This is to prevent rust from spreading to the other car components, and to keep your car in a good condition. Ignore the part about side mirrors. Unclip the electrical connector for the door lock button, and that should be it! Once removed, it is as simple as carefully placing … a wide and stout flat head screwdriver between the panel and the metal door structure and prying up gently with deliberate and controlled force. Pry up the arm rest with the flathead screwdriver and turn it upside down. Pop that out and remove the screw. I put a piece of construction paper around the end of it to avoid scratching any paint. Simply open the driver's side door and disengage the small switch on the edge of the door.
Once the control panel pops loose, carefully undo the plugs and look for the hidden 4th screw - near the grab handle area. Fortunately, they are easy to repair. Carefully pry at the small opening on the bottom of the speaker grill. Make sure the window is held in place while performing this step, or the window may fall into the door and break! Remove the Phillips head screw in the pocket of the arm rest. There is probably a specialized tool for this, but it is seemingly impossible to hook it from the top and pull it out. This article applies to the Honda Civic 1990-2000.
Don't forget to coat the area with primer and paint of the same color as your car. The problem could be the result of a broken part or larger electrical problem. As seen in the diagram above, the door-locking mechanism is comprised of many pieces. The only tools needed to remove the door panel include a Phillips head screwdriver and a flathead screwdriver or an automotive. Unplug the window control switch.
Remove the speaker mounting screws. Pull on the lower edge and sides of the panel to remove the plastic pop rivets. Remove the window crank if you have one see 3. This article applies to the. Pry the piece on the inside of the side view mirror out. Last, there are a miscellaneous plastic clips holding the panein place running along the outside edges on the backside of the panel those will all pop right out with a little force, now everything should be loose, so slide the panel back and up, simultaneously, and it should come right out. Starting at the back of the panel, lift the panel up and forward, being careful to navigate around the door lock post.
All of these screws are covered by the speaker grill. This helpful article will show you how. I've got my old regulator with a good motor and will redesign the sucker to work without having to replace it every year or so, but it would be good to have the removal instructions for the door panel so I won't tear it up trying to get to the regulator. There were no screws or anything to take out first, it just pops off. By - March 23, 2015 This article applies to the Honda Civic 1990-2000. However, taking the panels out to paint them. I have a 1996 Camry and it explained how to remove the trim around the inside door handle, where I was stuck in my removal process.
This article applies to the Honda Accord 1990-2002. Then you need to unlock the small lever connected to the inner door handle. Then unscrew the one Phillips head screw and set it aside. Note: I am not a registered charity. Detach the electrical connector and remove the speaker. Disconnect speaker wires Once panel is off, push in on the metal spring clips holding the black plastic boxes and slide off, re-attach to metal bracket on door panel makes install easier. Spin this clockwise to unlock it, then slide it up and out.