2000 chevy s10 torque specs. Chevy S 2019-04-03

2000 chevy s10 torque specs

Chevy S

2000 chevy s10 torque specs

And no sports car offers the utility of a pickup bed. In a crash, this applies force to the strong pelvic bones. Canadian vehicles indicate oil pressure in kPa kilopascals. The Chevy S10 has a width of 67 inches. Customer Satisfaction Procedure Customer Assistance for Text Telephone.

Next

Chevy S

2000 chevy s10 torque specs

The receiver will continue to scan and momentarily stop at each station until you press the button again. The wheel could come off and cause an accident. Then, to move the trailer to the left, just move that hand to the left. These accumulations can be a fire hazard. Turn the thumbwheel all the way up to turn on the interior lamps. Every 150,000 Miles 240 000 km : Cooling System Service or every 60 months, whichever occurs first.

Next

Chevy S10 Specs

2000 chevy s10 torque specs

During this time range it was offered in cars in Chevrolet Impala, Caprice, El Camino, and Monte Carlo. Defensive Driving Drunken Driving Control of a Vehicle Braking Steering Road Recovery. The pictures will help you locate them. If the vehicle slips off the jack, you could be badly injured or killed. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.

Next

4.3L Vortec Engine Specs

2000 chevy s10 torque specs

Reduce your speed according to your speedometer, not to your sense of motion. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. Pick up the latch plate and pull the belt across you. Air bags plus lap shoulder belts offer the best protection for adults, but not for young children and infants. Passlock enables fuel if the ignition lock cylinder is turned with a valid key. Inspect engine accessory drive belt.

Next

GM 2.2L

2000 chevy s10 torque specs

If a gasket is supplied with the replacement part, it should be used. The most important thing to know is this: let your engine do some of the slowing down. Make sure the tire is stored securely. Here are some rules to follow: If you use a step bumper hitch, your bumper could be damaged in sharp turns. Fan or fan and clutch assembly Serpentine drive belt if equipped by positioning the belt over the pulleys and carefully allow the tensioner back into contact with the belt.

Next

What do you torque the front axle hub nut on a 2000 s10

2000 chevy s10 torque specs

If you turn your engine off immediately after towing at high altitude on steep uphill grades, your vehicle may show signs similar to engine overheating. Extra fuses and the fuse extractor are provided in the cover. After the desired torque is reached, some bolts then require further rotation of a few degrees. The short bolts required 22 foot-pounds of torque and then a 55-degree rotation. You can also learn about some things you should not do with air bags and safety belts. There is also technical information about your vehicle, and a part devoted to its appearance care. Your front and rear turn signal lamps will flash on and off.

Next

Chevy S10 Specs

2000 chevy s10 torque specs

It should be worn over the shoulder at all times. After this the nut should go. Or is it just plain falling asleep at the wheel? Tighten the pulley bolts to 18 ft. Turn the knob toward the front of the vehicle to increase lumbar support and toward the rear of the vehicle to decrease lumbar support. Tighten the diagonal lower intake manifold bolts two on each end to7 Nm 62 lb in. Just clamp a tool on it as a handle and start tapping it sideto side with a hammer while pulling, and it should come out.

Next

What are the torque specs for a 2000 Chevy S10 water pump

2000 chevy s10 torque specs

Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement. Posted on Oct 01, 2010 Fig. Before you close the door, be sure the belt is out of the way. It should be 60 psi 420 kPa. Tighten the vertical lower intake manifold bolts the four middle ones to 13 Nm 115 lb in.

Next

Lower intake torque specification on 2000 chevy s10

2000 chevy s10 torque specs

All three systems have to do their work at the places where the tires meet the road. Lower Intake Manifold to Cylinder Head Bolt 8-12 - 71-106. If you have left the engine running, the vehicle can move suddenly. A crew cab model was introduced in 2001. Off roading can take you over hard packed dirt, gravel, rocks, grass, sand, mud, snow or ice. Fit the jack into the appropriate hole nearest the flat tire.

Next

Lower intake torque specification on 2000 chevy s10

2000 chevy s10 torque specs

Lubricate chassis components or every 3 months, whichever occurs first. When the clutch is engaged, the fan spins faster to provide more air to cool the engine. Your odometer shows how far your vehicle has been driven, in either miles used in the United States or kilometers used in Canada. To make the belt longer, tilt the latch plate and pull it along the belt. The diagnostic system can determine if the fuel cap has been left off or improperly installed. The player will pull it in.

Next