Ford used the axle through the end of the 1997 model year when the F-350 line was dropped and replaced by the 1999 F-350 Super Duty which initially only had a Dana 50 MonoBeam front Axle. As far as the F-350s I've never seen a one ton in a four wheel drive that didn't have a solid front axle. Not sure if it is true but I have heard that the Dana 50 and dana 60 are identicle on the outside but only bigger on the inside. But my question is whether or not the Dana 50 and Dana 60 have the same Rotors, hubs wheel bearing assemblies?? Disclaimer: Due to factors beyond the control of bayview auto repair, it cannot guarantee against unauthorized modifications of this information,. The new axle, which is rated for a 5,000-pound capacity was the first production Dana 60 front axle to use Ball Joints, but it still had serviceable wheel bearings and lockout hubs like the previous 1985-1991 King Pin axle. We stock a wide selection of parts and Tools for 1992 to 1997 Ford F-350 Dana 60 open knuckle front drive axles with Ball Joints. For instance my 97 f250 heavy duty powerstroke as the badges say came with the ttb, which was also one of the first things to go, it now sits as it should with a dana 60 up front.
In this video I will show you how to replace the u joint on the front axle or the drive shaft. The open knuckle, monobeam, Dana-Spicer Model 60 using Ball Joints instead of King Pins was introduced by Ford for the 1992 model year F-350 1 ton 4x4. . Please review the vehicle options and installation notes, to ensure you select the correct product for your Ford F-250. The heavier duty F250s staid with the solid axle. It just had heavier duty components, such as stronger axle shafts and the works. Axle Pivot Brackets - Tuff Country 20852 Rating: 4 Stars I added the Tuff Country leveling add-a-leaf leaf spring to the front of my truck which it desperately needed to bring the front up to the level of the rear.
We're here to help - please call us at 1-800-358-4751. I am doing this because the dana 50 needed ring gears and a few other things and I found this axle and it is just much much easier. I have a question about this, since many of you seem to know a lot about this. So i am thinking that the parts are all the same? I didn't purchase the drop brackets and the suspension arms were at way too much of an angle which was going to cause many problems both ride quality wise and wear on. It can be done and the two axles are identical for mounting to the truck.
Need assistance selecting the right Tuff Country product? I am replacing it within the next few days with a Dana 60. I am thinking that they do just becuase my dad has a 2002 F250 with the dana 50, but halfway through the year they switched to a Dana 60, but yet whenever he calls an autoparts store and needs any of those parts, the store never needs to know which axle is in it. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not bayview auto repair. Due to factors beyond the control of bayview auto repair , no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Listed below are the Axle Pivot Brackets that are designed to work with the 1993 Ford F-250.
One thing most people don't realize is though, the F250 with the twin I beam had the same axle housing as the F-150. I have a 1999 F350 that had the dana 50 in it. Shop now for Parts, Tools, and Manuals to fit 1992-1997 Ford F350 4x4 Trucks with Dana 60 Open Knuckle Front Axles. . . . .
. . . . . . .
. . . . . .
. . . . . . .
. . . . . .
. . . . .